Technical Specifications
SPL
118 dB
Amplifier Power
700 W Bass (Class D) + 150 W Midrange (Class D) + 150 W Treble (Class D)
Frequency Response
30 Hz - 43 kHz ("-6 dB")
Accuracy of Frequency Response
± 1.5 dB (36 Hz - 20 kHz)
Driver Dimensions
2 x H 137 x W 263 mm Bass + ⌀ 130 mm Midrange + ⌀ 25 mm Treble (view in inches)
Dimensions
H 593 x W 357 x D 347 mm, with Iso-Pod™ (view in inches)
Weight
31.9 kg / 70.3 lb
Connections
2 x RJ45 Control
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
8361A SAM™ Studio Monitor
SAM™ Studio Monitor
Technical Specifications
The flagship of The Ones range, the 8361A offers the most advanced acoustic performance of any studio monitor on the planet.
System Specifications
Frequency Response
36 Hz - 20 kHz (± 1.5 dB)
Low cutoff -6dB
30 Hz
High cutoff -6dB
43 kHz
SPL
Peak SPL
≥124 dB
Short term max SPL
≥118 dB
Long term max SPL Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
≥109 dB
Self-generated noise
Self-generated noise Self generated noise level in free space at 1 m on axis (A-weighted)
≤5 dB SPL
Weight
Weight31.9 kg (70.3 lb)
Dimensions
Height
570 mm
Height with Iso-Pod
593 mm
Width
357 mm
Depth
347 mm
Enclosure
Enclosure material
Die cast aluminium
Enclosure type
Reflex port
Drivers
Driver type
Racetrack
Dual 263 x 137 mm (103/8 x 53/8 in) obround cones
Count
2
Width
263 mm
Height
137 mm
Driver type
Coaxial
8361A midrange driver cone (coaxial)
Diameter
130 mm
Driver type
Coaxial
8361A treble driver metal dome (coaxial)
Diameter
25 mm
Directivity
Harmonic distortion
> 100 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF (top graph)
4.2 ms
Extended Phase Linearity in GLM set to ON (bottom graph)
8.6 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
700 W Class D
150 W Class D
150 W Class D
Mains voltage
100-240 VAC 50/60Hz
Power consumption
ISS Active
≤1.5 W
Idle
≤20 W
Full output
600 W
Signal processing section
Connectors
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm
Crossover
Bass/Mid
320 Hz
Mid/Treble
2800 Hz