Technical Specifications
SPL
118 dB
Amplifier Power
500 W Bass (Class D) + 250 W Midrange (Class D) + 200 W Treble (Class AB)
Frequency Response
32 Hz - 22 kHz ("-6 dB")
Accuracy of Frequency Response
± 2.5 dB (37 Hz - 20 kHz)
Driver Dimensions
⌀ 305 mm Bass + ⌀ 125 mm Midrange + ⌀ 25 mm Treble (view in inches)
Dimensions
H 680 x W 400 x D 380 mm, (view in inches)
Weight
42 kg / 92.6 lb
Connections
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1237A SAM™ Studio Monitor
SAM™ Studio Monitor
Technical Specifications
Reveal the finest details of your mix with a master of the modern studio - the smart three-way 1237A.
System Specifications
Frequency Response
37 Hz - 20 kHz (± 2.5 dB)
Low cutoff -6dB
32 Hz
High cutoff -6dB
22 kHz
SPL
Peak SPL
≥122 dB
Maximum peak acoustic output per pair in a listening room with music material at 2 m.
Short term max SPL
≥118 dB
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
Long term max SPL
≥112 dB
Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver unit protection circuit) at 1 m.
Self-generated noise
Self-generated noise
≤10 dB SPL
Self generated noise level in free field at 1 m on axis (A-weighted).
Weight
Weight42 kg (92.6 lb)
Dimensions
Height
680 mm
(26 3/4 in)
Width
400 mm
(15 3/4 in)
Depth
380 mm
(15 in)
Enclosure
Enclosure material
MDF
Enclosure type
Reflex port
Drivers
Driver type
Cone
305 mm (12 in) cone
Diameter
305 mm
(12 in)
Driver type
Cone
125 mm (5 in) cone
Diameter
125 mm
(4 7/8 in)
Driver type
Metal dome
25 mm (1 in) metal dome
Diameter
25 mm
(1 in)
Directivity
Harmonic distortion
> 200 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.0 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
500 W Class D
250 W Class D
200 W Class AB
Mains voltage
100-240 VAC 50/60Hz
Power consumption
ISS Active
≤0.5 W
Idle
≤25 W
Full output
750 W
Signal processing section
Connectors
Input
Analog signal input connector XLR female, balanced 10 kOhm.
Input
Digital signal input connector XLR female 110 Ohm.
Output
Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control
Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
