8361, 8351 and 7382 Immersive System

Big performance for big rooms. The huge dynamic range and transparent performance of this 7.1.6 system provides unbelievably realistic immersion – and will adapt to your room’s acoustic environment too.


Products in this solution:

Genelec 8361A Studio Monitor Front
7 × 8361A
Genelec 8351B Front
6 × 8351B
Genelec 7382A SAM Studio Subwoofer
1 × 7382A

Products in this solution

8361A

SPL

118 dB

Frequency Response

30 Hz - 43 kHz (-6dB)

Dimensions

H 593 x W 357 x D 347 mm, with Iso-Pod™ (view in inches)

8351B

SPL

113 dB

Frequency Response

32 Hz - 43 kHz (-6dB)

Dimensions

H 454 x W 287 x D 278 mm, with Iso-Pod™ (view in inches)

7382A

SPL

129 dB

Frequency Response

15 Hz - 100 Hz (-6dB)

Dimensions

H 625 x W 1400 x D 558 mm, (view in inches)

Key Technologies

Smart Active Monitoring (SAM™) and GLM™ calibration technology

Minimum Diffraction Coaxial (MDC™) Driver Technology

Minimum Diffraction Enclosure (MDE™) Technology

Directivity Control Waveguide (DCW™) Technology

Acoustically Concealed Woofers (ACW™) Technology

Protection Circuitry

Optimised Amplifiers

Reflex Port Design

Intelligent Signal Sensing (ISS™) Technology

Active Crossovers

Iso-Pod™ Stand

Versatile Mountings

Room Response Compensation

Bass Management System

Find Your Dealer

Type in your city to find your nearest Genelec dealer

Filters
X Filters
All
Studio monitors
Home speakers
AV Installation
Technical Service
Showroom
Experience Centre
SAM Certified
Smart IP Certified
Selected country

Documentation

FAQ

The Classic 8000 Series monitors have an analogue input. The 7200 Series SAM subwoofers have AES/EBU digital outputs only. However, other 7300 Series SAM subwoofers have analogue inputs and outputs and can be used also with analogue monitors.

Which SAM™ Products You Are Going to Mix With the Classic 8000 Series?
Mixing 8000 Series and SAM™ monitors is not recommended

We do not recommend mixing Classic 8000 Series monitors with SAM™ Monitors.
If the analogue input sensitivity of 8000 Series and SAM™ Series monitors are the same, Genelec SAM™ Monitors exhibit a slightly larger latency (< 5 ms) than 8000 Series monitors. Therefore Classic 8000 Series and SAM™ Series monitors should not be mixed in a stereo pair or multichannel setup.

It is alright to mix Classic 8000 Series with SAM™ Subwoofers

However, it is okay to mix the Classic 8000 Series monitors with SAM™ Subwoofers. Any Classic 8000 Series monitors can be used with SAM™ Subwoofers, in any stereo or multichannel setup.

Setting the room response calibration controls

Genelec monitors are calibrated flat in anechoic free field conditions. When the monitor is placed in a room close to walls or other boundaries, the low frequency output of the monitor increases. To achieve a flat low frequency response an adjustment of typically -4 dB on the bass tilt control is used. Genelec also provides a bass roll-off control to compensate for any remaining excessive LF energy around the low cut-off frequency.
Genelec GLM AutoCal can implement a more precise compensation after measuring the acoustic effects produced by the monitor’s installation location.

Differences in room reverberation time and listening distance can lead to changes being required in the treble region so treble tilt is fitted to most of the models in the Genelec range.

In three-way monitors and large main systems there are additional driver controls for the bass level, mid level and treble level which enable very fine adjustment of the frequency response so that the monitors can be placed in many different listening environments, whilst still achieving a consistent and neutral sound reproduction.

The best way to set the room response controls of a Genelec monitor is by taking an acoustical measurement at the listening location, using a measurement system for those products that offer local controls (DIP switches) on the monitor or subwoofer, or by using GLM AutoCal for the SAM™ (Smart Active Monitoring) products.